Ugrás a fő tartalomra Ugrás a kereséshez Ugrás a fő navigációhoz
Számtalan projektből szerzett tapasztalat
Kezdjük együtt!
Mi mások vagyunk. Mi jobbak vagyunk!
Gyors és közvetlen kapcsolat
Ajánlat
Ugrás a kezdőlapra

Electronic Spare Parts for Older Foundry Machines: Plug-in Boards, Obsolescence and Repair

Obsolete electronics title graphic: technician holding a control plug-in board with revision label in front of an open control cabinet
FISS Knowledge · Modernisation

Electronic Spare Parts for Older Foundry Machines: Plug-in Boards, Obsolescence and Repair

Frame, platens and hydraulics of a die casting machine can work for decades. The control cabinet ages faster: plug-in boards, PLC modules, drives and panels are discontinued long before the machine is worn out. Whether an older machine stays productive often depends on a few electronic spare parts.

Short Answer

What Are Obsolete Electronic Spare Parts?

Obsolete electronic spare parts are control components – plug-in boards, PLC CPUs and I/O modules, drives, panels – that their manufacturer no longer produces or supplies as new parts. A failure can then mean a long stop while a replacement is searched for, repaired or redesigned.

Obsolescence cannot be avoided, but it can be managed: know the life cycle status, rank parts by criticality, stock or repair the critical ones and back up programs – before the first failure.

Life Cycle

How Control Manufacturers Phase Out Electronic Components

Control manufacturers phase out products in stages. The table summarises how Siemens describes its life cycle milestones in its phase-out notice for the SIMATIC S7-300 and ET 200M (Siemens Industry Online Support, entry 109809890, accessed 6 November 2026).

Milestone (Siemens) What Siemens Says Consequence for the Machine Operator
PM400 – phase-out announcement Components remain available as new parts, but are removed from active marketing and the catalogue Time to record installed modules and plan stock or migration
PM410 – product cancellation Afterwards only available as spare parts or by repair; delivery may be in exchange for the defective part, in spare-part quantities only Extensions and new projects with this system become difficult
PM490 – discontinuation Components can no longer be ordered; only warranty cases are handled Supply depends on own stock, the used market and repair

According to the notice, PM490 is not planned before ten years after PM400, although Siemens cannot guarantee this for every assembly. Other manufacturers use other terms, but the announcement is always the signal to act.

Examples

SIMATIC S5 and S7-300: Two Examples of Phase-Out

Many older foundry machines run on Siemens controls. For the SIMATIC S5, Siemens wrote in its S5-to-S7 migration guide (04/2015) that the components had been discontinued since 2003, were then largely still available as spare parts – only in exchange for the old component – and that the number of available parts was continuously decreasing. A current Siemens page on S5 renewal states that the product has been discontinued and that the associated maintenance service period has ended.

For the SIMATIC S7-300 and the ET 200M I/O system, Siemens set the phase-out announcement (PM400) for 1 October 2023 and the product cancellation (PM410) for 1 October 2025. Siemens names the S7-1500 with ET 200MP as the functional replacement. Machines built in the 2000s are therefore now entering the situation S5 machines have been in for years.

Typical Electronics

Which Electronics Are Found in Older Foundry Machines?

Control

PLC, I/O and Plug-in Boards

PLC CPUs, I/O modules and, on many machines, manufacturer-specific boards in a card rack (CPU, input, output, power supply).

Shot End

Valve Amplifiers and Shot Control

Amplifier cards for proportional and servo valves; failures directly affect speed and pressure profiles.

Drives

Drives and Power Supplies

Frequency converters, older DC drives, power supplies and furnace temperature controllers.

Operation

Panels and Sensors

Operator panels, position transducers, pressure sensors and thermocouple amplifiers, often with special interfaces.

The machine-specific plug-in boards are usually the most critical items: unlike standard PLC modules, they are rarely available on the open market. FISS lists such parts in its accessories categories plug-in boards and electronic modules, including newly produced boards for controls of Frech die casting machines, together with repair and service.

Open electrical cabinet of a Bühler Carat 200 compact die casting machine with I/O modules and wiring
Electrical cabinet of a Bühler Carat 200 compact with I/O modules. Photo: FISS
Criticality Analysis

Criticality Analysis: Which Electronic Spare Parts Matter Most?

Obsolescence management ranks components by the consequence of a failure and the difficulty of replacement. IEC 62402:2019 Obsolescence management describes this approach in general form, from the management plan to the selection of resolutions.

01

Record the Installed Base

List every component with manufacturer, order number, hardware and firmware version – including rack boards.

02

Check the Life Cycle Status

Active, phase-out announced, spare parts only or discontinued?

03

Assess the Consequence of a Failure

Does a failure stop one machine, a cell or the melting shop? Is there a workaround?

04

Define the Measure per Part

Stock, repair agreement, tested used part, alternative or migration – recorded in the spare parts list.

Spare Part Options

Options for Obsolete Electronic Spare Parts Compared

Siemens states that it keeps spare parts for most industry products for ten years after the start of the phase-out and may offer remanufacturing or repair. After that, operators combine the following options.

Option Advantages Limitations
Original spare part from the manufacturer Defined version, manufacturer responsibility Only until discontinuation; often in exchange for the defective part
Used or surplus part Fast, available for common PLC modules Unknown history; must be tested; versions may differ
Board repair Original board and version are kept Requires diagrams or experience; repair time; not every fault can be repaired
Newly produced or reverse-engineered board Ends dependence on old stock Development effort; function and interfaces must be verified carefully
Own stock Shortest downtime Tied-up capital; stored electronics and batteries age too
Typical Example (Illustrative) An output board in the card rack of an older cold-chamber machine fails. With a tested spare on the shelf, the change takes hours; if the board must first be found or repaired, the stop can last weeks. The few machine-specific boards are the best place to invest in stock.
Risks

Risks When Replacing Electronic Spare Parts

  • ESD: handle boards only with ESD protection; IEC 61340-5-1:2024 sets requirements for ESD control programmes
  • Untested used parts: agree on a function test or test certificate before installation
  • Versions: compare hardware and firmware versions and DIP switch or jumper settings with the part being replaced
  • Batteries and memory: check backup batteries and memory modules before swapping CPUs
  • Safety functions: if the part belongs to a safety function, have the function tested and documented after replacement

In safety-related circuits, the machine’s safety documentation applies and the occupational safety specialist should be involved. See also CE Marking and Safety When Buying a Used Die Casting Machine.

Data Backup

Backing Up Programs and Parameters

A spare part is of little use if the program is lost. Siemens’ S5 migration guide points out that a program in battery-backed RAM is lost on voltage failure without a backup battery. Drive parameters and shot control settings are just as vulnerable.

  • Back up PLC programs, drive parameters and panel projects outside the machine
  • Keep matching programming software and a working programming device
  • Photograph board settings: switches, jumpers, potentiometers
  • Repeat the backup after every change and date it in the maintenance records

Backups belong in the routine described in Preventive Maintenance of Die Casting Machines.

Retrofit

When a Control Retrofit Becomes Unavoidable

Spare part management buys time, not forever. A control retrofit becomes unavoidable when critical parts can no longer be obtained or repaired, failures pile up, nobody can maintain the software or the cell needs interfaces the old control lacks. What a retrofit includes is explained in Overhaul or Retrofit? Modernising Used Foundry Machines.

Conclusion

Obsolescence Is Predictable – Downtime Does Not Have to Be

Obsolete electronic spare parts are normal for older foundry machines. Knowing the installed electronics, following phase-out notices, securing the critical boards and backing up programs keeps a sound machine running for years. After that, a planned retrofit beats a forced one.

Frequently Asked Questions

Questions About Electronic Spare Parts for Older Machines

Are SIMATIC S5 Spare Parts Still Available From Siemens?

Siemens states on its S5 renewal page that the product has been discontinued and that the associated maintenance service period has ended. S5 parts therefore come mainly from the used market, repair providers or own stock.

What Does PM410 Mean for an S7-300 Control?

PM410 is Siemens’ product cancellation milestone. For the S7-300 and ET 200M it took effect on 1 October 2025; since then, the components are only available as spare parts or by repair, in quantities customary for spare parts. Existing machines keep running, but spare parts planning becomes more important.

Can a Defective Plug-in Board Be Repaired?

In many cases, yes. Specialised service providers repair boards at component level, which keeps the original version and settings. Success depends on the fault, the documentation and the components on the board.

Is It Safe to Install a Used Electronic Module?

A used module should only be installed after a function test and a comparison of hardware version, firmware and settings with the original part. If the module is part of a safety function, the function must be tested and documented after replacement.

Looking for Plug-in Boards?

Electronic Spare Parts and Repair from FISS.

FISS lists plug-in boards and electronic modules for older machine controls and offers repair and service. Send FISS the order number and version of the part you need.

Sources

Siemens Industry Online Support: Information about the product phase-out of S7-300 / ET 200M components, entry ID 109809890 (milestones PM400, PM410, PM490), accessed 6 November 2026.

Siemens AG: Guide for Migrating SIMATIC S5 Projects to SIMATIC S7, entry ID 105106251, V1.0, 04/2015.

Siemens: SIMATIC S5 renewal service information, siemens.com, accessed 6 November 2026.

Siemens: Ersatzteilversorgung (spare parts supply), siemens.com, accessed 6 November 2026.

IEC 61340-5-1:2024, Edition 3.0 – Electrostatics – Part 5-1: Protection of electronic devices from electrostatic phenomena – General requirements.

IEC 62402:2019, Edition 2.0 – Obsolescence management.

FISS Machines: accessories categories Plug-in Boards and Electronic Modules, blog article Overhaul or Retrofit? Modernising Used Foundry Machines, fiss-machines.com, accessed 6 November 2026.